Ei Electronics Ei262 Manuel d'instructions

Instruction ManualRead and retain carefully for as long as the product is being used. It contains vital information on the operation and installation

The units will automatically exit house code after 30 minutes. Once coded the system will not communicate with any other RadioLINK devices outside the

Slide the Ei450 onto the mounting base on the wall.Check that the RadioLINK system is working by pressing the button on the Ei450 i-controller until t

Reset the house codeSometimes in order to resolve an RF communication issue, e.g. Alarms had to be relocated, it may necessary to reset and house code

4. OperationFrequent testing of the system is advised to ensure its continued and safe operation. Guidelines and best practices for testing are as fol

If there is a fire, immediately evacuate the premises and telephone the fire brigade.If the source of the alarm is not obvious go to the Ei450 i-contr

If you are satisfied there is no fire but the Smoke/Heat Alarm is still continuing to alarm you may now silence the system.Wait until the SILENCE segm

4. When the FIRE icon stops flashing, the memory recall is complete, the Alarm will stop sounding and the Alarm controller will return to standby with

The system diagnostic features are intended to assist professional installation and maintenance personal to install, commission and maintain the Radio

With the Ei450 in your hand press and hold the button. Walk around the house and verify that each Alarm is sounding. When testing is complete release

On entering the system diagnostic mode the TEST segment will flash green inviting you to press the button.When you press the button the segment will t

Contents1. Overview ...2. Installation ...

This will then locate the Alarm that was previously active and cause it to sound for a number of seconds (depending on the number of RadioLINK devices

6. GuaranteeEi Electronics guarantees the (‘Model Ei450’) for 5 years from date of purchase against any defects that are due to faulty materials or wo

7. Troubleshooting the RadioLINKIf, when checking the RadioLINK interconnection, some of the Alarms do not respond to the Ei450 remote control test, t

8. Limitations of Radio CommunicationsEi Electronics radio communication systems are very reliable and are tested to high standards. However, due to t

The user is encouraged to eliminate the interference by one or more of the following measures:(i) Re-orientate or re-locate the unit.(ii) Increase the

10. Getting the Ei450 servicedIf your Ei450 fails to work after you have carefully read all the instructions and checked that the unit has been instal

The crossed out wheelie bin symbol that is on your product indicates that this product should not be disposed of via the normal household

27

Aico LtdMile End Business Park,Maesbury Road, Oswestry,Shropshire SY10 8NN, U.K.Telephone: 0870 7584000www.aico.co.ukEi ElectronicsShannon Industrial

1. OverviewCongratulations on purchasing the Ei450 single button alarm controller for RadioLINK Fire and Carbon Monoxide (CO) Alarm systems. The Ei450

Fire / CO Alarm ControllerFire Indicator Low Battery Indicator CO IndicatorLight Segments (4)Segment Colour ActivityFunction enabledTest / Control But

Wireless Smoke Alarm System Wireless Smoke &Carbon Monoxide Alarm SystemRF Smoke AlarmRF Smoke AlarmRF Smoke AlarmAlarm ControllerRF Smoke AlarmRF

2. InstallationInstall the Ei450 mounting plate at an accessible point on the wall 1.4M +/- 200mm from floor level. If it intended for a disabled pers

Check the power up sequence• Fire, Battery & CO icons flash• Each individual segment lights up red• Each individual segment lights blue• Each

3. House CodingIt is essential to House Code the Ei450 i-controller to all the other RadioLINK Alarms and devices in the system to ensure they will no

Return to the Ei450 i-controller and check that all 4 segments (ring) are flashing blue. The number of flashes should equal the number of RadioLINK de